Elantas PDG Epoxylite® E230 Two-Component Epoxy Impregnating Resin
MFR #:Epoxylite® E230
EIS #:PH21-Epoxylite E230
MFR #:Epoxylite® E230
EIS #:PH21-Epoxylite E230
Elantas PDG Epoxylite® E230 Two-Component Epoxy Impregnating Resin, Epoxy Base Type, 1.1620 g/cm3 (77 °F (25 °C)) Density, 1700 V/Mil At 25 °C/77 °F - 3 Mil Dielectric Strength, 248 °C (ASTM D93) Flash Point, 16 hr At 60 °C/140 °F Full Cure Time, 15 - 25 min At 25 °C/77 °F (250 g) Gel Time, 75 - 85 Shore D Hardness, 100 (Parts By Weight And Volume) Resin, 20 (Parts By Weight) 22.6 (Parts By Volume) Hardener Mixing Ratio, 3000 - 6000 CP At 25 °C/77 °F Viscosity, 10000 - 15000 CP At 25 °C/77 °F (Material As Supplied) Viscosity - Part-A, 100 - 500 CP At 25 °C/77 °F Viscosity - Part-B. - Epoxylite® E 230 epoxy is a two-component, low temperature curing, 100%-solids resin system, secondary insulation.
$173.25
- $1,087.23
Select from the options below
Elantas PDG Epoxylite® E230 Two-Component Epoxy Impregnating Resin, Epoxy Base Type, 1.1620 g/cm3 (77 °F (25 °C)) Density, 1700 V/Mil At 25 °C/77 °F - 3 Mil Dielectric Strength, 248 °C (ASTM D93) Flash Point, 16 hr At 60 °C/140 °F Full Cure Time, 15 - 25 min At 25 °C/77 °F (250 g) Gel Time, 75 - 85 Shore D Hardness, 100 (Parts By Weight And Volume) Resin, 20 (Parts By Weight) 22.6 (Parts By Volume) Hardener Mixing Ratio, 3000 - 6000 CP At 25 °C/77 °F Viscosity, 10000 - 15000 CP At 25 °C/77 °F (Material As Supplied) Viscosity - Part-A, 100 - 500 CP At 25 °C/77 °F Viscosity - Part-B. - Epoxylite® E 230 epoxy is a two-component, low temperature curing, 100%-solids resin system, secondary insulation.
Product Options
Showing 3 out of 3 options
 | Container Size: 4 Oz | EIS Part #: EPO230MKIT | $ / Case Pack: 20/Case | |
| Container Size: 2 lb | EIS Part #: EPO2302LB | $ / each | |
| Container Size: 1 lb | EIS Part #: EPO2301LB | $ / each |
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameEpoxy Impregnating Resin
Trade NameEpoxylite®
SeriesEpoxylite® E230
General Features
Net Weight9.5 - 9.9 lb
Shelf Life12 Months
TypeTwo-Component
Design & Construction
Base TypeEpoxy
ColorAmber
FormLiquid
Performance Details
Full Cure Time16 hr at 60 °C/140 °F
Gel Time15 min
Technical Details
Flash Point248 °C
Chemical Properties
Mixing Ratio100 (Parts By Weight and Volume) Resin, 20 (Parts By Weight) 22.6 (Parts By Volume) Hardener
Viscosity3000 cP
Viscosity - Part-A10000 cP
Viscosity - Part-B100 cP
Electrical Properties
Dielectric Strength1700 V/Mil
Physical Properties
Hardness75 - 85 Shore D
Features
- Excellent penetration in trickle application
- High bond strength
- Chemical, refrigerant and moisture resistant
- Fast cure with low heat
- Ideal for appliance motors and other high-speed rotating devices
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- Trickle application method
- 40 Pounds at 25 °C / 77 °F, 4 Pounds at 150 °C / 302 °F helical coil bond strength (ASTM D2519 over MW 35)
- < 1.0% (NEMA RE-2) R-22 extractable material
- 0.2% (24 hours at 25 °C / 77 °F) water absorption
- 1.1 x 10^15 Ohm-cm (ASTM D257 - 25 °C / 77 °F) volume resistivity
- 3.8 at 1 kHz - 25 °C / 77 °F dielectric constant
- 0.03 at 1 kHz - 25 °C / 77 °F dissipation factor
- Gel Time: 15 - 25 min at 25 °C/77 °F (250 g)
- Gel Time: 15 - 25 min
- Viscosity: 3000 - 6000 cP
- Viscosity - Part-A: 10000 - 15000 cP
- Viscosity - Part-B: 100 - 500 cP
Applications
- Impregnation of Motor and Transformer Windings Including High-Speed Armatures, Protective Overcoat for Motor Windings